CAN.init_Filt()

[CANBus]

説明

Function to filter CAN ID. On the 86Duino platform, there are 32 groups of CAN ID filters. When receiving data from the CAN bus, these filter ID can be used to determine whether the data need to be handled.
Combining with the init_Mask() function, receiving data can be limited to CAN ID within the A ~ B range.
When this function is used in a sketch without calling the init_Mask() or init)Filt() function first, data from all CAN ID will be accepted.

構文

CAN.init_Filt(num, ext, ulData)

媒介変数

• num: Identify filter ID to be used, within the 0 ~ 31 range.
  ext: data transmission format. There are 4 different options:
  • CAN_STDID: Standard data frame, comply with CAN 2.0A standard. ID range: 0 ~ 0x7FF
  • CAN_EXTID: Extended data frame, comply with CAN 2.0B standard. ID range: 0 ~ 0x1FFFFFFF
  • CAN_STDID_REMOTE: Standard remote frame, comply with CAN 2.0A standard. ID range: 0 ~ 0x7FF
  • CAN_EXTID_REMOTE: Extended remote frame, comply with CAN 2.0B standard. ID range: 0 ~ 0x1FFFFFFF
• ulData: Filter value. Refer to the following example:

        Without mask:
        0 0 0 0 0 0 1 1    Filter ID value: 0x03
        0 0 0 0 0 0 0 0    Mask: 0x00
        Range of CAN ID to receive data:: 0x03
        With mask
        0 0 0 1 1 0 0 1    Filter ID value: 0x19
        0 0 0 0 0 0 0 1    Mask: 0x01
        Range of CAN ID to receive data:0x18、0x19
        0 1 0 1 1 1 0 0    Filter ID value: 0x5C
        0 0 0 0 0 1 1 1    Mask: 0x07
        Range of CAN ID to receive data:0x58 ～ 0x5F

戻り値

• CAN_FAIL: Setting failed
• CAN_OK: Setting success

事例

#include <CANBus.h>
unsigned char buf[8] = {0, 1, 2, 3, 4, 5, 6, 7};
 
void setup() {
    Serial.begin(115200);
    CAN.begin(CAN_500KBPS); // Configure CAN bus transmission speed to 500KBPS
    CAN.init_Filt(0, CAN_STDID, 0x019); // Configure filter ID 0 to 0x019, using Standard data frame
    CAN.init_Mask(0, CAN_STDID, 0x01); // Configure mask for filter ID 0 to 0x01, using standard data frame
}
 
void loop() {
    CAN.beginTransmission(0x00, CAN_STDID);    // Set external CAN ID to 0x00, using standard data frame
    CAN.write(buf, 8);                         // Transmit 8 bytes of data
    CAN.endTransmission();                     // End transmission
    delay(10);
}

参照

• init_Mask()
• beginTransmission()
• write()
• endTransmission()

ライブラリリファレンスホーム

86Duinoリファレンスのテキストは、Arduinoリファレンスを改変したもので、Creative Commons Attribution-ShareAlike 3.0ライセンスに基づいてライセンスされています。リファレンス内のコードサンプルはパブリックドメインとして公開されています。